Ultrasonic Mist Maker Fogger Humidifier Transformer with 10 Heads 5-7L/h
Free Shipping to USA and Worldwide
Instructions 1. When using atomizer, need to be equipped with power supply (output power ≥300W, output voltage is DC64 ±2V); when using ring-shaped jade changer (convert AC220V into AC36V), plate (convert AC36V into DC48V) . 2. The is connected to the power supply. The is placed flat in the water. The is turned upside down and fully immersed in the water. The electricity can be turned on. When the is energized, the water is not taken out. Hold the atomizer upside down to avoid damage. 3. The water level above the atomizer water level sensor is about 1CM, the atomization effect is appropriate, the water is too deep, and it needs to be equipped with a buoy 4. The mist generated by the atomizer needs to be exhausted by the fan to prevent the water temperature from rising due to the retained water in the mist, shortening the life of the atomizer. 5. When multiple atomizers are placed in one container (with an interval not exceeding 1M), the quality inspection housings of the atomizers must be conducted to prevent electrical corrosion of the atomizer housing and damage the atomizer. 6. After the atomizer has worked for a long time, scale will be deposited on the surface of the housing and the atomizing sheet, which will affect the service life and atomization effect. Therefore, it is recommended to clear the atomizer once every 2 months. When cleaning, it is recommended to gently scrub with a soft cloth. Water flush 7. When the atomizer installation process avoids damage to the water level switch, so as to avoid failure of the water level switch, resulting in loss of control of the atomizer, it will cause the atomization piece to dry, which will seriously damage the atomizer. 8. When you stop using the , disconnect the power supply and remove the from the water 9. Atomizer for neutral (PH = 7) atomization of acidic solution, can not be in the strong acid or alkaline solution atomization 10. Don't take the atomizer out of the water when it is powered on, or hold it upside down; the atomizer cannot be placed high on one side and lower on the side of the atomizer; the atomizer will first power off and take out the water. 11. Found that the atomizer ruptured, immediately power outage, the atomizer out of the water, to avoid the water from the broken atomizer into the atomizer plate, even the atomizer short-circuit burnout.
Application: 1.Waterscape pool manufacturing fog 2.Spinning humidification 3.Tobacco humidification 4.Mushroom humidification 5.Greenhouse flowers humidification 6. Printed Electronics humidification
Parameter: 1. Atomizers Voltage: DC48V Power: 230W(5L)，250W(7L) Current: 3.7A Spray volume: 5kg/h(5L) or 7kg/h(7L) Water supply pressure：0.01~0.2Mpa Size: 253*88*28mm Working water temperature: 5~55°C Working water level: 9cm (depth greater than 15CM, buoy required) Working environment: The atomizer must be placed in water to work. Neutral water (tap water, pure water, etc.) and weak acid solution can only be atomized. Do not atomize alkaline solutions, strong acid solutions, and alcohol.
2. Transformer Working principle: Convert AC220V to DC48V Input voltage: AC220V Output voltage: DC48V Power: 350W (One power supply only support one atomizer),720W (One power supply can support two atomizer), Precautions: 1. The transformer (switching power supply) must not be placed in a damp place. It should not be sealed. Use it in a dry and ventilated place. 2. Plug wire: Yellow wire grounding wire, zero wire Fire wire wire N, L
3. Waterproof power supply Working principle: Convert AC220V to DC48V Input voltage: AC220V Output voltage: DC48V Power:350W Precautions: The power supply should not be placed in water and it should not be exposed to sunlight. The power supply can rain and can be used in a wet place. It is recommended to use it in a cool, ventilated place.
4. Bouy Work: control the working level of the atomizer